PreFlight Checklist

FREE RESOURCE

Pre-Flight Checklist

A comprehensive 27-point inspection checklist for commercial drone operators. Print it, laminate it, and use it before every single mission.

Why You Need a Pre-Flight Checklist

Professional drone operations are not about talent — they are about process. Every licensed commercial pilot in Zimbabwe should follow a standardized pre-flight procedure before launching. This checklist prevents battery failures, firmware glitches, airspace violations, and the kind of mistakes that destroy client trust and equipment.

This checklist is based on CAAZ operational requirements, DJI manufacturer recommendations, and real-world practices from working commercial pilots in Harare and Bulawayo. Print it out, keep it in your drone case, and tick every box before you arm your motors.

A Pre-Departure (At Home / Office)

  • Batteries charged to 100% — Confirm all flight batteries and controller battery are fully charged. Check battery health in the DJI Fly or DJI Pilot 2 app. Reject any battery showing swelling, damage, or fewer than 80% health cycles remaining.
  • Firmware is current — Open the DJI app and check for aircraft, controller, and battery firmware updates. Never fly on outdated firmware — it can cause GPS lock failures and gimbal errors.
  • SD card formatted and inserted — Format your microSD card in-camera (not on a computer) to prevent file corruption. Verify you have enough storage for the entire mission. Carry a backup card.
  • Mission planning complete — Review your flight area on Google Earth or DJI FlightHub. Identify obstacles (power lines, cell towers, trees). Plan your takeoff and landing zone. Set waypoints if applicable.
  • NOTAM and airspace check — Verify there are no active Notices to Airmen for your flight area. Confirm you are not within controlled airspace (CTR) of Harare, Bulawayo, Victoria Falls, or any military zone without prior CAAZ authorization.
  • Weather assessment — Check wind speed (max 10 m/s for most consumer drones, 12 m/s for enterprise), precipitation forecast, and visibility. Do not fly in rain, fog, or thunderstorm conditions.
  • Client brief and permissions — Confirm the client knows the flight plan, expected deliverables, and timeline. Ensure you have written permission from the property owner or site manager to operate on their premises.

B On-Site Physical Inspection

  • Propellers secure and undamaged — Inspect each propeller for cracks, chips, or bending. Ensure all propellers are firmly locked in place. Replace any propeller that shows signs of wear.
  • Gimbal and camera lens clean — Remove the gimbal cover/clamp. Inspect the gimbal for free movement in all axes. Clean the camera lens with a microfiber cloth. Check for condensation (common in Zimbabwe's humid eastern highlands).
  • Motor arms locked and motors spin freely — For folding drones (Mavic series), confirm all arms are fully extended and locked. Gently spin each motor by hand — there should be no grinding, resistance, or unusual noise.
  • Landing gear and sensors clean — Check underside sensors (vision positioning system) for dirt, dust, or stickers. Dirty sensors cause erratic hovering at low altitude. Wipe with a dry cloth.
  • Battery inserted and seated properly — Click the battery firmly into position. Verify the battery latch is fully engaged. Power on and check battery temperature — do not fly if the battery is below 15°C (rare in Zimbabwe but possible at high altitude).
  • Antenna orientation on controller — Position controller antennas so the flat faces point toward the drone. This maximizes signal strength. Never fly with antennas pointed at the tips — signal drops dramatically.

C Software & System Checks (After Power On)

  • GPS satellite lock acquired — Wait for a minimum of 12 satellites before takeoff. In Zimbabwe, you typically get 14–18 satellites in open areas. Fewer than 10 satellites means unreliable position hold — do not fly.
  • Home point recorded — Verify the home point is set to your current location (shown on the map in the app). This is where the drone returns to in case of signal loss or low battery RTH.
  • Return-to-Home altitude set — Set RTH altitude at least 30 meters above the tallest obstacle in your operating area. For urban environments in Harare, 60–80 meters is recommended.
  • Flight mode confirmed — Verify you are in the correct flight mode (P-mode / Normal for standard operations, or Waypoint/Mission mode for survey work). Do not fly in Sport mode for commercial work unless specifically required.
  • Camera settings configured — Set resolution, frame rate, white balance, and exposure before takeoff. For mapping: mechanical shutter, 1/1000s minimum, ISO 100–200. For video: 4K/30fps, D-Log or HLG profile.
  • Obstacle avoidance ON — Confirm all obstacle avoidance sensors are enabled. Only disable if you are an experienced pilot performing a specific maneuver that requires it (e.g., flying backwards through a narrow gap).
  • Max altitude and distance limits set — Set maximum altitude to 120 meters AGL (400 feet) as per CAAZ regulations unless you have specific authorization for higher operations. Set distance limit appropriate to your VLOS capability.

D Immediate Pre-Takeoff

  • Takeoff area clear of people — Ensure a minimum 5-meter radius around the takeoff point is clear of bystanders, children, and animals. Brief any on-site personnel to stay clear during launch and landing.
  • Wind check at ground level — Feel the wind direction and estimate speed. If tree branches are swaying significantly, reconsider the flight. Ground-level wind is typically 40–60% of wind speed at operating altitude.
  • Visual observer briefed (if applicable) — If you have a spotter, confirm communication method (radio, hand signals, or verbal), emergency procedures, and their observation zone.
  • Record start time in flight log — Note the date, time, location (GPS coordinates), battery serial number, pilot name, and mission type in your logbook. CAAZ may request this during audits or RPL renewal.
  • Compass calibration (if prompted) — Only calibrate if the app requests it. Calibrate away from metal structures, vehicles, and reinforced concrete. In Harare's CBD, magnetic interference is common — calibrate before driving to the site if possible.
  • Test hover at 3 meters for 15 seconds — After takeoff, hover at 3 meters and observe. The drone should hold position steadily without drifting. If it drifts, land immediately and recalibrate or troubleshoot. Check for any unusual sounds from the motors.
  • Confirm recording has started — Before flying to your mission area, press record and verify the red recording indicator is active. Check that footage is actually writing to the SD card (timer should be counting up). Nothing is worse than flying a perfect mission with no footage.

Post-Flight Procedure

After landing, complete these steps to protect your equipment and maintain your records:

  • Power off the drone before the controller. Always power off in this order: drone first, then controller. This prevents the drone from entering failsafe mode.
  • Remove and inspect the battery. Check for swelling or excessive heat. If the battery is too hot to hold comfortably, allow it to cool before storing. Note the remaining charge percentage.
  • Back up all footage immediately. Copy SD card contents to two separate locations (laptop + external drive or cloud). Do not format the card until backup is confirmed.
  • Complete your flight log entry. Record end time, total flight duration, any incidents or anomalies, and number of photos/videos captured.
  • Clean the drone. Wipe down the body, sensors, and lens. Store in the carry case with propellers folded and gimbal cover attached.
Back to Home

No comments:

Post a Comment